AVDI Diagnostics Price List

ABRITES Diagnostics for Audi, VW, Seat, Skoda, Bentley

Special function for adapting electronic modules for VAG vehicles

Extracting and displaying immobilizer related data by diagnostic. Ability for alignment of immobilizer related data - cluster/ecu. Displaying immobilizer related data from dump of flash and eeprom of micronas mcu in IPC.
Read/Program memory of instrument cluster immobilizer
Read/Update immobilizer related data
Read/Update immobilizer data in VDO dashboards with NEC microcontroller (2009+) by OBDII
Extracting and displaying PIN code, control module configuration memory content, component security data from engine control units EDC16, MED9.x, Simos PPD 1.1/1.5, Magneti Marelli 4HV,7GV. Emergency start for engine control units EDC16. The whole EEPROM could be read for EDC15/ME7/EDC16. For MED9 and Simos engine control units only the PIN/CS/MAC is displayed.
Advanced Diagnostic Functionality - Ability to manage stored crash data and configuration memory of electronic control unit. Read/Update Config Data of airbag control units Siemens (CAN bus - ISO15765). Audi A6/Q7/Allroad, VW Golf5..., Skoda Octavia II ..., Seat Altea ... With this special function, you can Read/Update ConfData memory of the airbag module. Clear the crash data of the airbag module.
Covered units for Read/Update ConfData:
1. All Siemens CAN Airbags 2003-2008 like 4F0959655B (Audi A6/Q7/Allroad 2003-2008),
1K0909605AB, 1K0909605C, 1K0909605AD, etc...
2. K-Line Airbags (Siemens and Bosch) - 1C0 909 605 C, 8L0 959 655 A, 1J0 909 609, 6Q0 909
605 C,6Q0 909 605 A, 6Q0 909 605 B, 3B0 959 655 B, 1C0 909 605 F, 1C0 909 605 H, 1J0 909
607, 1J0 909 603, 4B0 959 655 C, 4B0 959 655 J, 4D0 959 655 C, 8L0 959 655 F,8A0 959 655
C, 8A0 959 655 K, 8A0 959 655 K, 4D0 959 655 H, 8D0 959 655 C, 8D0 959 655 L
Preparation of a key ready for adaptation by diagnostic to the vehicles with BCM2 - Audi A4, S4, RS4, A5, S5, RS5, A6, A7, A8, Q5 / VW Touareg
+ ILM Front passenger ((ILM Beifahrer) - Audi A8 2003-2010
Component protection generation 2
EZS-Kessy Audi A6/Q7 2004-2009 by OBDII
Comfort module Audi A6/Q7 2004-2009 by OBDII
Climantronic Audi A6/Q7 2004-2009 by OBDII
Airbag Audi A6/Q7 2004-2009 by OBDII
Airbag Audi A4/A5/Q5 2008+ from Bosch by OBDII
Instrument cluster Audi A6/Q7 2004-2009 by OBDII
Instrument Cluster Audi A4/A5/Q5 2008+ by OBDII
Infotainment electr. Audi A4/A5/Q5 2008+ by OBDII
- All other modules (e.g. DSP) with component protection generation 2
for A6/Q7 2004-2009 and A4/A5/A5 possible only if you have dump from gateway from where module was originally build
+ Adaptation of engine control units to the vehicle - EDC16,EDC17, MED17, MED9, Simos PPD, ME7.5.20, ME7.5.30
Kessy Audi A8/VW Touareg/Phaeton
Comfort module VW Passat B6/CC
Transmission gearbox Audi A6/Q7/Allroad/A8
EZS-Kessy Audi A6/Q7/Allroad
BCM2 immobilzier - Audi A4, S4, RS4, A5,S5, RS5, A6, A7, A8, Q5 / VW Touareg
+read the PIN and CS of the EDC17/MED17 engine control units. With this function is possible to read even engine control units 2012+ which are with
updated software and is not possible to read normally by OBDII.With this special function the EDC17/MED17 is not read through OBDII - you should have direct connection to the engine
control unit. It is possible to make this on the table, you need to connect only 12V, GND, Ignition, CAN-H and CAN-L. It is possible to read the ECU also in the car, but you need to find
somewhere the CAN-H (orange-black) and CAN-L (orange-brown) wires. So connect them to the AVDI and you will be able to read the engine control units.
+ adapt the transmission control unit (TCU) to the immobilizer (BCM2). For that purpose is necessary first to read the TCU. The TCU is not possible to be read by OBDII,
but is possible to read it when you connect the TCU on the table, or when you connect the AVDI to the internal CAN-Bus of the car.
To read from the internal CAN-Bus, find the orange/black and orange/brown CAN wires and make the following connection of the AVDI:
- orange/black <-> CAN-H (PIN6 of the OBDII)
- orange/brown <-> CAN-L (PIN14 of the OBDII)
- Ground <-> GND (PIN4 of the OBDII)
- 12V <-> 12V (PIN16 of the OBDII)
+reading the PIN/CS/MAC of the Simos PCR 2.1 engine control unit.
NOTE: This function requires internet access

New AVDI Interface or active AMS is required to purchase this special function.

Special function for learning keys to VAG vehicles

+Extracting and displaying immobilizer related data by diagnostic. Ability for alignment of immobilizer related data - cluster/ecu. Displaying immobilizer related data from dump of flash and eeprom of micronas mcu in IPC
Read/Program memory of instrument cluster immobilizer
Read/Update immobilizer related data
Read/Update immobilizer data in VDO dashboards with NEC microcontroller (2009+) by OBDII
+ Extracting and displaying PIN code, control module configuration memory content, component security data from engine control units EDC16, MED9.x, Simos PPD 1.1/1.5, Magneti Marelli 4HV,7GV. Emergency start for engine control units EDC16. The whole EEPROM could be read for EDC15/ME7/EDC16. For MED9 and Simos engine control units only the PIN/CS/MAC is displayed.
+ This function will allow the preparation of a key ready for adaptation by diagnostic to the vehicles with BCM2 - Audi A4, S4, RS4, A5,S5, RS5, A6, A7, A8, Q5 / VW Touareg
+ Guided key adaptation functions, preparation keys suitable for the vehicle (dealer's keys). Included are also Audi A6, Audi Q7, Audi Allroad, VW Crafter(with EDC16 ECU), VW Passat, (BCM2 based vehicles are supported only with the help of ABProg*)
Key programming/adaptation
Reading security code (PIN) and component protection by OBDII - VW CRAFTER
EZS - Kessy (Q7/A6/Allroad) - With this function you can prepare dealer key/learn dealer key- Read/Update ConfData from EZS - Kessy (Q7/A6/Allroad)
Programming keys by OBDII (VAG with 16 bytes Component Security) - VW Crafter, Audi R8, VW Golf 6, VW Multivan 2009+, VW EOS 2009+, VW Caddy 2009+, VW Scirocco, VW Polo 2009+, VW Bora 2010+, VW Jetta 2010+, Skoda Octavia II 2009+, Skoda Superb 2009+, Skoda Fabia 2009+, Skoda Yeti 2009+, Seat Leon 2009+, Seat Altea 2009+, Seat Exeo 2009+, Seat Ibiza 2009+, ...
Extracting of the 7th byte Component Security from a working key of the car (Megamos, Hitag2)
LAMBORGHINI GALLARDO
Key learning for Audi A6/A7/A8 with ALL KEYs LOST.

New AVDI Interface or active AMS is required to purchase this special function.

The function allows to replace immo-related parts in another vehicle, even when the brand is different or the power class is different.

The function works for the transmissions of Audi A6 2003-2010, Audi Q7 2005-2015, Audi A8 2003-2010,

and for all Immo III/IV engine control units where writing is not permitted. (EDC16/EDC17/ME7/MED9/MED17/Simos benzin/Simos PPD/Simos PCR/Magneti Marelli/Delphi). The function requires internet connection and a complete VN002.

Attention:

The VN005 special function requires VN002 as well as an additional cable set (ZN052) that allows you to start and complete the operation. Each module that is adapted (TCU or ECU) will require an EM003 emulator to be built inside the car.

The function allows the programming of keys to ALL VEHICLES with Immo III/IV immobiliser systems and Megamos 48 transponders.

The function works both when there is a working key and in ALL KEYS LOST situations.

A ZN053 AVDI extractor cable IS REQUIRED when purchasing the special function.

The procedure also requires a ZN051 Distribution Box and an internet connection.

Mileage recalibration for vehicles based on the MQB platform from 2014 onwards.

Active AMS and internet connection are required.

Key programming for vehicles based on the MQB platform. This includes all models starting from 2012 onwards. 

PROTAG programmer, active AMS and internet connection are required.

Reading the PIN and Component Security of the Magneti Marelli 9GV ECU. Procedure is done by OBDII with a working key or on the bench (using the ZN051 Distribution Box without opening the ECU) when all keys are lost.

Performing authorization (using the ZN051 Distribution Box) of the vehicle ECU in order to update the engine software or to start the vehicle for ALL IMMO 3/IMMO 4 ECUs (Bosch, Siemens/Continental and Magneti Marelli). Allows entering into reflashing mode to update with a SGO/FRF file or to perform an emergency start to the vehicle. 

Odometer recalibration for VAG vehicles 

-Mileage recalibration for Audi A6/A7 (4G) and A8 (D4) and VW Touareg 7P produced from 2010 until 2017 BY OBDII. 
The function works with UDS dashboards.
-Reading and updating internal control module configuration memory by diagnostics. 
Extracting and recalibration security access codes, PIN, component security bytes, current unit mileage values by K-line, CAN bus and UDS. 
-Cluster CAN - With this function you can establish a disgnostic session with the instrument cluster using KWP2000 over TP2.0 or UDS. 
You can Read/Update the odometer values. Supported types are: - VDO/MM/Visteon -2007 (CAN TP2.0)- VDO with NEC μC 2009+ (CAN UDS)- JCI with NEC μC 
and 95320 EEPROM (CAN UDS)- Magneti Marelli with 9S12 μC (CAN UDS)- A8(4H)/A7(4G)/A6(4G)/Touareg(7P) with 95320 EEPROM (CAN UDS)
-Cluster K-Line - With this function you can establish a disgnostic session with the Instrument cluster via K-Line 
(KWP1281 or KWP2000); You can Read/update the odometer value; Read PIN code; Read/Update ConfData; Read ROM/Flash from the Instrument cluster; 
Automatic removing of "DEF error" for Audi A4 instrument cluster BOSCH RB8. Supported types are:- VDO66/86, Motometer- External Immobilizer - LT, 
VW GOL, VW O GOL( Kostal ), Siemens 6 PIN HC05 Immo/TMS- Audi A4 B5 with/without board computer -1997- Audi A6 -1997- Audi A8 -1999- Magneti Marelli - Shadow 1/2/3/Direct- 
VW Sharan/Galaxy -2000- Audi A4 Bosch RBx/RB4/RB4 Crypto/RB8 Crypto 2004+- Golf 4 Bosch RBx- VW Phaeton/Touareg, Bentley Continental, 
Porsche Cayenne- Seat Exeo Bosch RB8 Crypto 2008+- Lamborghini Gallardo -2005/2005+
-Read/Update ConfData (VAG-EDC15x, VAG-ME7.1.1, VAG-ME7.1, VAG-ME7.5, VAG-Cartronic ME7.8.)
-Extracting Security access code / PIN (EDC15, ME7.x, VAG-Cartronic ME7.8) - Extracting Component security bytes 
(EDC15, ME7.x, VAG-Cartronic ME7.8)- Mileage Calibration (EDC15, EDC16)

Full set of mileage recalibration special functions for VAG. 

Full set of key programming special functions for VAG. The following hardware IS REQUIRED in order to obtain full functionality:

ZN002 PROTAG Programmer

ZN051 Distribution Box

ZN053 AVDI Extractor Cable

Full set of special functions for VAG. The following hardware IS REQUIRED in order to obtain full functionality:

ZN002 PROTAG Programmer

ZN051 Distribution Box

ZN052 Abrites cable set for adapting IMMO parts used together with VN005

ZN053 AVDI Extractor Cable

ABRITES Diagnostics for Mercedes, Smart, Maybach

Generating of key dumps for vehicles with DAS-2, DAS-2A, DAS-2B, DAS-3.Smart key programming. Read partially data of the EIS. Read/update configuration data of the ESL. Virgin ESL. Resetting ETC (722.9) and ISM by diagnostic to the factory state without losing of SCN coding. Infra Red and password reader, Personalization, Activation, Coding.

ZN036 IS REQUIRED when purchasing the special function.

This special function is dedicated to the latest generation Mercedes-Benz FBS4 (DAS) related modules. It allows the following for modules installed in Mercedes vehicles equipped with the FBS4 generation of DAS:

- Renewal of FBS4 control modules including 7G Tronic units 722.9. ALL BY OBD or internal CANBUS.
- Renewal of FBS4 CRD 3.X Engine Control Units. ALL BY OBD or internal CANBUS.

Both functions are performed using the new online Mercedes software.

Instrument Cluster Data Manager, TV, ECU, Airbag Manager
- Updating data memory instrument clusters W221, W216, W219, X164, W164, W203, W251, W463, R171, W209, W220, W215, W169, W245, Smart (2007+), W204, X204, W212, W197, W207, W218,W168, W202, W140, W210, W211, W461, W208, W163, W230, Sprinter, Vito, Viano
- Modifying ASSYST and ASSYST PLUS service history records 
- Updating data memory in Battery Control Module, Tyre Pressure Monitor, Electric Seat Adjustment Driver and Electric Seat Adjustment Passenger, Rear Signal Acquisition and Actuation Module 1, Electronic Stability Program (ESP), Airbag, Electronic Parking Brake, Vehicle Power Supply Control Module 
- Reading and updating flash and configuration memory of ECUs: Siemens SID, EDC15, EDC16
- Service list update
- TV, AUX on/off configuration
- Managing stored crash data and configuration memory of electronic control unit
- Speed warning for Gulf States, reverse warning

Consists of all special functions for Mercedes-Benz vehicles. (This does note include the necessary hardware)

ABRITES Diagnostics for BMW, Mini

Programming keys by diagnostic. Supported type of units are CAS1, CAS2, CAS3, CAS3+

Perform synchronization/recovery between CAS, EGS and ECU (6-speed gearboxes in E-series vehicles) and adaptation of 8-speed gearboxes in F-series vehicles

Reading and programming vehicle order data, reprogramming flash memory of all electronic control units, E-series unit coding

Preparing keys by dump for BMW models with FEM/BDC and CAS4 immobilizer systems - newest BMW 1, 3, 5 GT, 6, 7, X3 series (body Fxx). Please note this functions also covers mileage reset in FEM/BDC modules in F-series BMW vehicles. 

ZN002 - PROTAG Programmer is required for key programming

Full set of special functions for BMW. ZN002 - PROTAG Programmer is required for key programming

ABRITES Diagnostics for Renault

Reading and updating flash and configuration memory of the ECUs. Clearing IMMO code data

Key programming functionality. Please note that this function also includes the RR015 special function. 

Allows clearing stored crash data in the unit produced from Temic and Continental (it supports units utilizing the CAN protocol). EPS and UCH renewal is also done using RR014. The function allows you to restore the modules to their factory virgin state and install a used module in a different vehicle.

This function is designed to assist Smart and Renault specialists when a second key needs to be learned for these cars. The function requires at least one working key for the car to be present as ALL KEYS LOST is still not covered.

Reading and updating internal control module configuration memory by diagnostic

Key programming functionality both for key addition and ALL KEYS LOST situations for Renault Talisman/Megane IV/Scenic IV/Espace V. RR012 is required for the purchase of this function.

Full set of key programming special functions for Renault vehicles. ZN002 PROTAG Programmer is required in order to obtain full functionality. 

ABRITES Diagnostics for Peugeot, Citroen

Reading and updating flash and configuration memory of ECUs: Siemens SID, EDC15, EDC16. Service list update.

Update of Instrument Cluster and BSI working data.

Display PIN code - diagnostic access.

ABRITES Diagnostics for Ford, Mazda

Reading and updating internal control module configuration memory by diagnostic.

Key programming functionality , InCode calculator needed for adaptation of new electronic control units (and keys also).

This function allows the clearing of the crash data from the RCM module using 4 simple button clicks. Read, clear, write, clear DTCs. The function covers the RCMs using the following processor: XC23xx data flash
For FORD/Mazda/JLR and Volvo as well as Ford/JLR RCMs with the following processor: TMS470 + EEPROM 25320/25640

ABRITES Diagnostics for Porsche

Reading and updating internal control module configuration memory by diagnostic. Recalibration of control unit working characteristics ( time,mileage).

Coding, configuration, key programming, PIN code calculation.

Allows the adaptation of modules both part of the Immobilizer system (Immo V) and those with component protection for Panamera, Cayenne 2011+, 911 991/Boxster 981, Spyder, Macan

ABRITES Diagnostics for Toyota, Lexus, Scion

Key programming functionality. Immobilizer/Smart system reset by diagnostic. Master key preparation by dump of smart system. Identification Control Unit reset by LIN bus. Master key emulation for all models with smart keys. Emergency start in all keys lost situations.

ZN039-2 IS REQUIRED when purchasing the special function.

ABRITES Diagnostics for Fiat, Alfa, Lancia

Update of Instrument Cluster working data.

Reading and Updating ECU's flash memory by diagnostic. ECUs supported: IAW 4AF,4EF,59F,5AF,5AM,5NF, 5SF3; MJD 6JF

Reading and Updating ECU's configuration memory by diagnostic. Reset to factory new state option. ECUs supported: EDC15C5, EDC15C7, MJD 6JF/8F2; Marelli IAW 4AF, 4EF, 59F, 5AF, 5AM, 5NF, 5SF3, 5SF8; BOSCH ME7.3H4 (boot), ME7.3.1 (boot).

Key programming. Transponders/Keys preparation. BCM - Configuration data read and update, PIN, component protection data display. Remote control programming.

ABRITES Diagnostics for GM (former Opel, Vauxhall)

Reading and Updating ECU's flash by diagnostics (OBDII).

PIN code calculation and key programming functionality, reading and updating of ConfData of ECU, instrument clusters and BCM units.

Calibration of instrument cluster and engine control module data, reset of airbag data (for certain models), extraction of radio PIN code by diagnostics (OBDII).

ABRITES Diagnostics for Mitsubishi

Reading and Updating ECU's flash and configuration memory by diagnostic.ECU EDC15

PIN code calculation and key programming functionality.

ABRITES Diagnostics for Subaru

Key learning for keyless and mechanical key Subaru cars even when all keys are lost. By OBD, no disassembly needed. Smart system reset is also possible.The function allows you to adapt new and used ECU (ECM) and Smart ECM

ABRITES Diagnostics for Nissan

Calculation PIN code (including 20-digit PIN Code) and programming keys by diagnostic.

ABRITES Diagnostics for Hyundai, Kia

Update of Instrument Cluster working data, Flash read/update for ECUs EDC15C2, EDC15C2 configuration memory update.

Key programming for all vehicles with smart keys (2018+). PIN code display for vehicles with mechanical keys - Delphi, KEFICO, EDC15/16. Flash Read/update for ECUs EDC16. 

Reduced price for owners of special function HK006. Please contact info@keyprogtools.com for details. 

ABRITES Diagnostics for Volvo

Update of Instrument Cluster working data.

Key learning for HITAG 2 PCF7945/7953 type of keys for 2008+ cars

ABRITES Diagnostics for Jaguar and Land Rover

Key programming functionality.

Update of Instrument Cluster working data.

ABRITES Diagnostics for Chrysler, Dodge, Jeep

Reading and updating configuration memory instrument clusters.

Reading and Updating ECU's flash and configuration memory by diagnostic. ECU EDC15/16

ABRITES Tag Key Tool - software for TAGPROG/PROTAG

This software will provide you access to the internal memory and configuration of transponders.Available tool for generation of keys by dump of immobilizer system of the vehicle (more than 1000 models are covered).Provided is the ability for preliminary preparation of transponders to be ready for usage with diagnostic equipment.Available functionality for cloning of Megamos 13, Temic 11, Temic 12, Texas 4C, PIT ID33, Tiris 4D, Tiris 4E, Temic 8C (Mazda, Ford, Proton).

Utility for displaying information from different keys (VIN, last drive, mileage,..).

Key programming by dump from the Electronics Body Front Section control unit (with Motorola MCU inside - 9S12XDP512, XEP100)

ABRITES ECU Programming Tool

Programming tool dedicated to reading/writing/updating of the Configuration Data (EEPROM), Internal and External Flash of Bosch EDC17/MED17, Delphi and SIMxx by boot mode.

ABRITES Diagnostics for Bikes, Snowmobiles, Water scooters

ABRITES Diagnostics for DAF

Key programming functionality.

By using the switches on the emulator, you can benefit from a 3-in-1 solution that supports the following models: W203, W204, W207, W208, W209, W210, W211, W212, W169, W245, Vito, Viano and Sprinter. This is a plug and play solution for most models. You can use the ABRITES Software for Mercedes to personalize the emulator (FREE OF CHARGE, NO TOKENS - available for all AVDI owners with valid AMS and special function MN026) or you can personalize the emulator with a green key in the same way as an original ESL (necessary ONLY for W204, W207 and W212).

The ABRITES ESL emulator for Renault vehicles (EM002) is one of the most advanced ESL emulators currently available. The ABRITES ESL emulator is part of the all new ABRITES design, manufacturing and development process which allows the whole emulator unit to be designed, developed and produced in-house by us. The currently supported models include Renault Megane II, Megane III, Laguna III, Scenic III, Clio IV and Fluence.

Used to emulate any IMMO part while emulating using VN005.

The CAN filter allows the unlocking of video playback in a moving vehicle in cases when this option is not available in the diagnostic coding options of the vehicle. This filter works with W166/W292 vehicles with NTG5s1 multimedia module (Panasonic). 

The CAN filter allows the unlocking of video playback in a moving vehicle in cases when this option is not available in the diagnostic coding options of the vehicle. This filter works with W221/W216 vehicles with NTG3.5 multimedia module. 

The odometer calibration emulator allows mileage calibration for W204 and W212 vehicles (both FBS3 AND FBS4).

The odometer calibration emulator allows mileage calibration for W204 and W212 vehicles (both FBS3 AND FBS4) and has jumper cable for the dash for easier installation.

Adapter for ABPROG programmer. It allows programming of EEPROMs – M35xxx/I2C/SPI/MicroWire. This adapter is a part from ABPROG programmer (ZN030).

The adapter is intended for ABPROG programmer ZN030 to be used with NEC MCUs from Mercedes IR-keys.

The adapter is intended to be used with the ABPROG Programmer ZN030 for reading NEC MCUs from Mercedes IR-Keys by soldering the MCU to the adapter.

The adapter is intended to be used with the ABPROG Programmer ZN030 to read CPUs and MCUs.

Cable for reading data from EIS through Infra Red

Adapter for diagnostics of all multimedia modules present in the car (Radio, Navigation, Bluetooth, Telephone, e.t.c)

Diagnostics adapter for ABS (Anti Lock Brakes), HALF (Haptical Lane Feedback), ESL ( Electronic Steering Lock), ORC (Occupant Restraint), EPS (Electric Power Steering), PAM (Parking Aid Module) present in Fiat 500x and Jeep Renegade

Transponder emulator required to complete the key learning/emergency start procedures part of the TN006 special function. You NEED to have TN006 active in order to use the emulator.

The Abrites A6/A7/A8 CAN Adapter is used in order to make the ALL KEYS LOST procedure for Audi A6/A7/A8 easier providing all necessary connections.

The Abrites key renewal adapter is a new product which assists when you need to renew a Hitag 2 type of key. It is soldered to the Hitag 2 PCB and it is then attached to the ABPROG programmer in order to renew used HITAG 2 keys.

The Abrites Renault key card type field detector has been developed in order to assist when testing to confirm whether or not the electronic ignition switch is functional before starting work. This field detector provides the customer with a reassurance before starting to work on a certain car The ZN047 is activated at 125KHz to confirm the operation of the unit. It indicates that a field is detected by a green light from the LED inside and it is shaped as a Renault key card in order to fit in the key-card slot of modern Renault vehicles.

The Abrites universal field detector has been developed in order to assist when testing to confirm whether or not the electronic ignition switch is functional before starting work. It detects a field of 125KHz and also a field of 20KHz so that it can be used for multiple brands of vehicles Such as Mercedes, Audi, Toyota and other brands which use these frequencies.

Adapter used to connect to K-Line BMW vehicles when using OEM software via the AVDI PassThru driver

Wire extender for the EEPROM/BCM adapter to be used for reading chips without having to take them off the PCB. 

Adapter used to read the V850E2 single-chip microcontroller using the ABPROG programmer. 

Adapter used to enter service mode for VAG VDO dashboards.

Adapter used to enter service mode for VAG Micronas dashboards with the new style connector.

Adapter will allow diagnostic operation with SAE J1850 based diagnostic protocols used in the past from Chrysler, Dodge, Jeep, Plymouth, Ford.

This cable is a part of PROTAG and ABPROG programmers (ZN002, ZN030)

Cable used to connect the AVDI and PROTAG programmer to the computer